TS2000 & Cqrlog help!

3 posts / 0 new
Last post
TS2000 & Cqrlog help!

73 to all !

Using Cqrlog Ver: 2.5.2 on ubuntu 20.04

I want to be able to communicate with my TS2000 rtx and cqrlog. Unfortunately it doesn't work..
I have add the user to the “dialout” supplementary group:
sudo usermod -a -G dialout giuliano
I checked that everything was ok after logout and login
giuliano@Pc-Giuliano:~$ id -Gn giuliano
giuliano adm dialout cdrom sudo dip plugdev lpadmin lxd sambashare
then, If run rigctl from console:
giuliano@Pc-Giuliano:~$ rigctl -m 214 -r /dev/ttyS0 -s 57600
Rig command: m
Mode: CW
Passband: 500
Rig command: f
Frequency: 14041580
Rig command: q
Ts2000 responds correctly to all commands!
if I run the cqrlog program from the console, this happens:
giuliano@Pc-Giuliano:~$ cqrlog --debug
Gtk-Message: 19:00:42.975: Failed to load module "canberra-gtk-module"
Cqrlog Ver:2.5.2 (001) Date:2021-02-12
**** DEBUG LEVEL 0 ****
**** CHANGE WITH --debug=1 PARAMETER ****
Linux version 5.8.0-53-generic (buildd@lcy01-amd64-012) (gcc (Ubuntu 9.3.0-17ubuntu1~20.04) 9.3.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #60~20.04.1-Ubuntu SMP Thu May 6 09:52:46 UTC 2021
2021-05-30 19:00:45 0 [Note] /usr/sbin/mysqld (mysqld 10.3.29-MariaDB-0ubuntu0.20.04.1) starting as process 2547 ...
RigCtldArgs:-m 214 -r /dev/ttyS0 -t 4532 -s 57600
RunRigCtld: FALSE
RigDevice: /dev/ttyS0
RigPoll: 500
RigId: 214
Not started rigctld process. (Run is set FALSE)
Connected to rigctld @ localhost:4532
Sending: fmv
Sending: fmv
Sending: fmv
Sending: fmv
Sending: fmv
Sending: fmv
Sending: fmv

Here my TRX Control configuration screen:


Sorry, I'm a beginner and I sure have made a mistake to configuring the program ..
I also use cqrlog on my notebook with yaesu FT-817 on /dev/ttyUSB0 for my activity / P without nothing problems!
Before asking for help I looked on the forum and in the faq, but I did not find anything about it..

Vy tnx in advance for all your help!

giuliano in3klq

TS2000 & Cqrlog help!

Hi Giuliano!

Debug says:
"Not started rigctld process. (Run is set FALSE)"

It looks like you have not checked preferences/TRXcontrol "Run rigctld at program start". Please check that! It is in the middle part of rig settings view.


Hi Saku,

Hi Saku,

Thank you for your answer!!

I just tested what you recommended and checked in TRXcontrol "Run rigctld at program startup" it was ok (see my link in the previous message ..)
Anyway I solved!
It was enough to have a little patience! in fact, when I open cqrlog if it doesn't communicate with ts-2000 I go to file -> refresh trx / rot control and it communicates perfectly! These beginners .. !!
73 Giuliano in3klq